Ouellet OCB Manuale Utente Scaricare il pdf

MAINTENANCE

- Once a year or at the need, remove the front panel and use

a vacuum cleaner to remove the dust accumulation inside

the heater.

- Cleaning should be done while the heater is disconnected

from the main service panel. Wait until the housing and

heating element cool before performing maintenance.

Remove the front panel.

CAUTION: Fins on the element are sharp - Do not touch.

Replace all covers before energizing.

- Any other servicing should be performed by a qualiﬁ ed

technician.

WARRANTY

Ouellet Canada inc. warrants the electric heating

element of the OCB Series for a one (1) year period; and

their component parts against defects in material and

workmanship for a one (1) year period following the date

of purchase, under normal use and service, when proof

of purchase of such is provided to the manufacturer. The

obligation of Ouellet Canada inc., under the terms of this

warranty, will be to supply a new unit and this omits the

manufacturer to bear the installation costs or other secondary

charges linked to replacing the unit or the component part(s).

INS24-200408-01

Thermostat

Element

Heating

Hight Limit

Element

Heating

WIRING DIAGRAM

180, 3

Avenue, L’Islet (Quebec) G0R 2C0 CANADA

Tel. : (418) 247-3947/1 800 463-7043, Fax : (418) 247-7801

www.ouellet.com

INSTALLATION INSTRUCTIONS

‘‘OCB’’ Series

THE INSTALLATION MUST BE EXECUTED

BY A QUALIFIED TECHNICIAN

RISK OF ELECTROCUTION

IMPORTANT INSTRUCTIONS

Basic precautions should always be followed to reduce

the risk of ﬁ re, electric shock, and injury.

- Read all instructions before using this heater.

- A heater has hot and arcing or sparking parts inside.

Do not use in areas where gasoline, paint or ﬂ ammable

liquids are used or stored.

- This heater is hot when in use. To avoid burns, do not let

bare skin touch hot surfaces. Keep combustible materials,

like furniture, pillows, bedding, papers, clothes, and

curtains at least 3 in. (76 mm) from the front of the heater.

- To prevent a possible ﬁ re, do not block air intakes and/or

exhaust in any way whatsoever.

- Do not insert or allow foreign objects to enter any ventilation

or exhaust opening as this may cause an electric shock or

ﬁ re, or damage the heater.

- Do not install heater against combustible low-density

cellulose ﬁ berboard surfaces.

- The heater is not to be located below electrical convenience

receptables.

- WARNING - High temperature: Keep electrical cords, drapes,

and other furnishings away from heater.

- Use only with copper branch circuit conductors.

- For bathroom use, the heater must be installed so that

switches and other controls cannot be touched by anyone

in the bath or shower.

- To avoid possible electrical shock, disconnect all power

at the main panel prior to wiring, cleaning, or servicing.

- Do not use outdoors.

- Use this heater only as described in this manual. Any other

use not recommended by the manufacturer may cause ﬁ re,

electric shock, or injury.

KEEP THESE INSTRUCTIONS

INSTALLATION / USER

With the option ‘‘Bottom fresh air inlet’’, install bottom of

heater not less than 3 in. (76 mm) above ﬁ nished ﬂ oor.

1- Remove baseboard front panel and junction box cover.

2- Remove appropriate knockouts.

3- Install the relay or the thermostat if it applies.

See options section for details.

4- Connect wiring supply according to the appropriate wiring

diagram in accordance with local and national codes.

5- Secure heater to the wall and loosen screws by 1/2 turn for

thermal expansion.

6- Replace junction box cover and baseboard front panel before

energizing.

OPTIONS

All heating equipment and options must be installed in accordance

with local and national codes.

Built-in thermostat:

- Fasten the thermostat using the 2 mounting holes at the top

of the right side connection box.

- Fasten the bulb to the wiring channel using the plastic straps

in the punched holes.

Built-in relays:

- Fasten the relay to the separating plate using a conduit nut.

- Insert the assembly in the right hand connection box.

- Fasten the plate using 2 screws to the left wall of the

connection box.

- Make connections as relay wiring diagram.

INTERCONNECTION

- The connection boxes and the wiring channel are approved for

interconnection of baseboard heaters and components which

are on the same heating branch circuit.

- For all other options in this series, use ‘‘EMT’’ or ‘‘BX’’ tubing

to pass wiring.

- The heater junction box minimum volume without options is

42.6 in³ (698 cm³).

CORNERS AND BLANK SECTIONS

- Install blank sections the same way as this heating unit.

- Install corners using the mounting holes.

- Do not disassemble the unit.

Sommario

Pagina 1 - KEEP THESE INSTRUCTIONS

MAINTENANCE- Once a year or at the need, remove the front panel and use a vacuum cleaner to remove the dust accumulation inside the heater. - Cl

Più documenti per Bollitori per acqua Ouellet OCB

Per vedere il documento Ouellet OCB Manuale Utente

Ouellet OCB Manuale Utente (1 pagine)

Commenti su questo manuale

Nessun commento

Ouellet OCB Manuale Utente

Navigare online o scaricare Manuale Utente per Bollitori per acqua Ouellet OCB. Ouellet OCB User Manual Manuale Utente

Sommario

Più documenti per Bollitori per acqua Ouellet OCB

Commenti su questo manuale

Prodotti e manuali riguardandi Bollitori per acqua Ouellet OCB