Ouellet ORC Manuale Utente Scaricare il pdf

Installation instructions and safety measures

INS96-200512-06

WARNING

Read Carefully - These instructions contain vital information for

the proper installation, use and efﬁ cient operation of the heater.

Carefully read these instructions before installation, operation of

the heater. Failure to adhere to the instructions could result in ﬁ re,

electric shock, serious personal injury, death or property damage.

Save these instructions and review frequently for continuing safe

operation and instruction of future users.

ATTENTION

1. Carefully read these instructions before installation.

2. Do not recess the heater.

3. Never paint the heater.

4. Never install the heater on a wall covered with vinyl.

5. Heater should not be blocked in any manner.

6. Install the heater in horizontal position only.

7. Allow 1 in. (25 mm) minimum clearance below heater and

any fabric. See Figure 4.

8. Allow 4 in. (102 mm) minimum clearance from dry wall

ceiling. See Figure 4.

9. Allow 4 1/2 in. (114 mm) minimum from false ceiling, vinyl

ceiling and plastic molding. See Figure 4.

10. Allow 1/2 in. (13 mm) minimum clearance between heaters.

11. Allow 3 ft. (915 mm) minimum clearance between the heater

and a device sensitive to heat of 40°C and higher

(104°F and higher).

12. Use supplied wall brackets required.

. To avoid electric shock, disconnect all power coming to

heater at main service panel before wiring or servicing.

14. This heater is hot when in use. To avoid burns, do not install

this heater in an accessible place. Allow 6 ft. (1829 mm)

minimum clearance from the ﬂ oor. See Figure 4.

ATTENTION (continuation)

15. Do not use plastic connector for direct connection

to the heater. Use power supply wire suitable for at least

90 °C (194 °F).

16. All wiring must be done in accordance with the national and

local electrical codes and the heater must be grounded.

17. A badly installed heater can be permanently damaged

and present a risk of ﬁ re or electric shock. Respect the

required minimal clearances. See Figure 1 and 4.

The heater must be solidly ﬁ xed to the structure of the

building.

18. Do not install the heater in bathrooms of vapor or showers,

directly over a shower cubicle, nor in places where it will be

exposed to high humidity or vapours during a long period.

19. Check voltage rating of heater to make sure it is same as

supply voltage.

20. Do not insert or allow foreign objects to enter any ventilation

opening as this may cause electric shock, ﬁ re, or damage

to the heater.

21. Do not block air inlet or outlet in any manner.

22. Heater contains arcing or sparking parts. Do not use in areas

where gasoline, paint, or ﬂ ammable liquids are used or stored.

23. Use this heater only as described in these instructions.

Any other use not recommended by the manufacturer may

cause ﬁ re, electric shock, or injury to persons.

KEEP THESE INSTRUCTIONS

END TO END INSTALLATION

1. Mount heaters allowing adequate spacing of 1/2 in. (13 mm)

minimum between heaters.

2. Install the splice plate as per instructions provided with the

« ORC-JT » kit. (OPTIONAL)

INSTALLATION AT CORNER

Heater must be located so that the ends of each heater

are 4 in. (102 mm) from side wall. See Figure 1.

WALL INSTALLATION

1. Use 2 wall brackets for the 450W to 900W.

Use 3 wall brackets for the 1050W and more.

Fix wall brackets so that, once the heater is installed on

the brackets, the length of the heater is supported at

equal intervals.

2. Fix the brackets with the provided wood screws.

Use template provided to mark screw location depending upon

type of ceiling.

3. Install the wire connector (not supplied) in one of the

knockouts onto the back shield.

4. Attach the back shield to the brackets by tilting it back and

allowing the bracket hook to enter the back shield slot then

simply bring back the shield forward locking it into place.

See Figure 2.

5. Insert the wiring in the junction box. Leave

approximately 6 in. (152 mm) of wiring in the case to facilitate

the wiring. IMPORTANT: Use power supply wire suitable

for at least 90 °C (194 °F).

6. Add the screw to secure the whole. See Figure 2.

7. Complete the wiring. See Figure 5.

8. Install end caps. See Figure 3.

WARRANTY

Ouellet Canada Inc. warrants the electric heating element of the

ORC Series for a ten (10) year period; and their component parts

against defects in material and workmanship for a one (1) year

period following the date of purchase, under normal use and service,

when proof of purchase of such is provided to the manufacturer. The

obligation of Ouellet Canada Inc., under the terms of this warranty,

will be to supply a new unit and this omits the manufacturer to bear

the installation costs or other secondary charges linked to replacing

the unit or the component part(s).

Figure 3

Figure 1

4 in.

(102 mm)

4 in.

(102 mm)

180, 3

Avenue, L’Islet, Quebec, G0R 2C0, CANADA

Tel.: (418) 247-3947, 1 800 463-7043

Fax: (418) 247-7801

www.ouellet.com

INSTALLATION INSTRUCTIONS

‘‘ORC’’ Series

THE INSTALLATION MUST BE EXECUTED

BY A QUALIFIED TECHNICIAN

RISK OF ELECTROCUTION

Step 1

Step 2

Figure 2

Leave 3/16 in. (5 mm ) between

the screw’s head and the bracket

1 2

Sommario

Pagina 1 - ‘‘ORC’’ Series

Installation instructions and safety measures INS96-200512-06WARNINGRead Carefully - These instructions contain vital information for the proper insta

Pagina 2

Double-poleThermostat(option)Single-poleThermostat(option)L1L2/NElementFigure 5 OPTIONS WIRING DIAGRAMWALLCEILINGTOP VIEWREAR VIEW34 in. to 113 in.(86